All behavior has
A) A good reason
B) Ethical endangerment
C) Danger
D) Consequences
Answer: d consequences
Explanation:
Which recovery equipment maintenance practice should be performed on a regular
basis
Regular equipment maintenance practices should include checking the recovery device for refrigerant leaks.
What is recovery equipment?They often include a combination of winching gloves, snatch blocks, tree saver straps, tow straps, kinetic recovery straps, recovery dampers, and winch line extensions.Recovery of refrigerant from a system using the compressor and/or internal pressure of the refrigeration system is referred to as system-dependent (passive) recovery. Appliances with more than 15 pounds of refrigerant cannot be utilized with system-dependent equipment.Whether or not the appliance compressor is operational, self-contained (active) recovery equipment has its own method of removing refrigerant from appliances and is able to achieve the necessary recovery rates. • Refrigerant is stored in a pressurized recovery tank by self-contained recovery equipment.To learn more about recovery equipment refer to:
https://brainly.com/question/29110277
#SPJ9
technician a says an out-of-round drum can cause a pulsating brake pedal. technician b says an out-of-round drum can cause the brakes to grab. who is correct?
According to the question of the pulsating brake pedal, both A and B are correct.
What causes brake pulsation?
Brake pulsation is mainly caused by warped rotors/brake discs. Excessive hard braking or quick stops, which can significantly overheat the discs, are the primary causes of deformed rotors. When the discs overheat, the composition of the metal disc material changes, resulting in imperfections in the metal's surface. Hotspots are noticeable irregularities. They appear as discoloured areas of the disc material, which are often bluish or blackish in appearance. The brake pedal is the pedal which you press with your foot to slow or stop a vehicle. When the driver presses the brake pedal, the system automatically delivers the appropriate pressure required to prevent colliding with the vehicle in front.
To learn more about brake pulsation
https://brainly.com/question/28779956
#SPj4
Link generation using microsites is a practice of. SEO
Link generation using microsites is a practice of White Hat SEO.
What is microsite?
A microsite is a single web page or a small group of web pages that are designed to supplement an offline activity or work as a separate entity (like an iFrame) within an already-existing website. The primary landing page for the microsite may have a separate domain or subdomain. In web design, microsites are frequently used to add a specific group of data, either editorial as well as commercial. When a site is used temporarily, such sites may be removed entirely from the server, linked in or out to the main site, or both. A microsite's primary difference from its parent site is how focused and purposeful it is in comparison to the microsite's larger parent website.
To learn more about microsite
https://brainly.com/question/17193001
#SPJ1
The space between two square flat parallel plate is filled with oil. Each side of
the plate is 600mm. The thickness of the oil films is 12.5mm. The upper
plate, which moves at 2.5m /s, requires a force of 98.1 N to maintain the
speed. Determine
I.The dynamic viscosity of the oil in poise.
Ii.The kinematic viscosity of the oil in strokes if the specific gravity of the oil
is 0.95
The dynamic viscosity of the oil in poise is 13.625 pois
The kinematic viscosity of the oil in strokes is 14.34
How to solve for the dynamic viscosityF viscous is given as n* ΔFr / Δy
where n = F * Δy / A * ΔVn
We have to define the terms of the formula
Δy = 12.5 x 10⁻³
ΔVr = 2.5m /s
A = 60 x 60 cm² = 0.36m
F = 98.1 n
We have to put the values in the formula
98.1 n * 12.5 x 10⁻³ / 0.36m * 2.5m /s
n = 1.3625 ns / m²
The kinematic viscosity of the oil in strokes if the specific gravity of the oil is 0.95
y = n / e
n = 1.3625
e = 0.95 x 10³
y = 1.3625 / 0.95 x 10³
= 1.434 x 10⁻³
Read more on dynamic viscosity here: https://brainly.com/question/13087865
#SPJ1
what could happen if the engine was uncowled during the starting and operating procedures
If an engine fails during rollout or just before takeoff, immediately shut both throttles and land the aircraft safely. Before reaching a safe single engine speed right away after takeoff, drop your nose to increase velocity.
What is the engine starting procedure?Closing the throttle, turning off the fuel pump, setting the mixture control to idle cutoff, and simply cranking the engine is the most reliable hot start method I've found.
What is the procedure for engine failure?If an engine fails during rollout or just before takeoff, immediately shut both throttles and land the aircraft safely. Before reaching a safe single engine speed right away after takeoff, drop your nose to increase velocity. If you are unable to climb, close both throttles and land straight ahead.
What happens if engine fails during take off?The typical practice for the majority of aircraft would be to abandon takeoff if an engine failed during takeoff. In small aircraft, the pilot should turn the throttles down to idle, activate the speed brakes (if provided), and apply the brakes as needed if the engine fails before VR (Rotation Speed).
To learn more about engine procedure refer to:
https://brainly.com/question/18428188
#SPJ1
The Cargo Tarp and Bow Assembly are stowed in?
The cargo tarp and bow assembly are stowed in the rear of the vehicle.
What is assembly?
During manufacturing, assembly is the process of integrating different components to create a final product. An assembly can also refer to a single-level, multilevel, or top-level bill of material (BOM). Mechanical, electrical, or software components can be found in assemblies. It combines all of the preceding stages of design, engineering, production, and logistics to produce an object that serves a purpose. The assembly operation is the second fundamental type of manufacturing, in which components are permanently or semipermanently connected together. Permanent methods of connecting components are employed in applications where the components must remain together and cannot be easily removed.
To learn more about assembly
https://brainly.com/question/15171397
#SPJ1
I need a word problem for y=2x
The word problem for y = 2x is as follows.
"If y is the number of cakes produced by using 2 amounts of backing ingredients (x), find the number of cakes produced if x is 25."
What is a word problem?A word problem is a mathematical exercise in scientific education in which substantial background information about the subject is conveyed in regular English rather than mathematical notation.
A word problem in mathematics is a math question expressed as one or more sentences that demand students to apply their arithmetic skills to a real-life setting.
This implies that in order to understand the word problem, students must be conversant with the terminology linked with the mathematical symbols to which they are used.
Learn more about word problems:
https://brainly.com/question/2610134
#SPJ1
A mathematics professor Mr. Cuba has two cubes on his table. Cuba arranges these two cubes daily to show the
current day of the month. Which 6 numbers do you think will be on the sides of either of these cubes to make
this happen? What steps shall he take daily? You can't represent the day 9 with only one cube. You have to use
both cubes all the time. So the 9th day would be "09", and 15th day would be "15"
Answer:
The six numbers on the cubes' sides are 0, 1, 2, 3, 4, and 5. Mr. Cuba would need to arrange the cubes each day to represent the current day of the month. For example, on the 9th day, he would put the cubes to show "09"; on the 15th day, he would arrange the cubes to show "15".
Explanation:
determine the required diameter of a steel transmission shaft 10 m in length and of yield strength 350 mpa
The required diameter of a steel transmission shaft 10 m in length and of yield strength 350 mpa is 0.02795m
What is steel?
Steel is an iron alloy that contains a few tenths of a percent carbon to increase its strength and fracture resistance when compared to other types of iron. Many additional elements could exist or be added. Stainless steels that are corrosion- and oxidation-resistant often require an additional 11% chromium. Steel's high tensile strength and low cost make it useful in constructions, infrastructure, tools, ships, trains, automobiles, machinery, electrical appliances, armament, and rockets. The foundation metal of steel is iron.
Neglecting shaft weight Design the shaft using maximum shear stress theory and determine the required diameter
factor of safety = 1.5
length of shaft = 10 meters
material yield strength = 350 MPa
Torque = 500 N.m
The required shaft diameter = 0.02795 m
To learn more about steel
https://brainly.com/question/23413124
#SPJ4
1. A 150 v moving iron voltmeter is intended for 50HZ, has a resistance of 3kQ. Find the series resistance required to extent the range of instrument to 300v. If the 300V instrument is used to measure a d.c. voltage of 200V. Find the voltage across the meter?
Answer:
Voltmeter reactance = 2π × 50 × 0.7 = 220ΩImpedance of voltmeter = 3000 + j220 = 3008Ω When the voltmeter range is doubled its impedance has also to be doubled in order to have the same current for full-scale deflection. If R is the required series resistance then 3000 + R2 + 2202 = 2 × 30082 ∴ R = 3012Ω When used on d.c. supply if the voltmeter reads 200 V the actual applied d.c. voltage would be = 200 × Total A.C. Impedance/total d.c. resistance = 200 × 2 × 3008/3000 + 3012 = 200 × 6016 × 6012 = 200.134V.
how should firefighters, when arriving on the scene of a working fire, use the exterior marking on a building that indicates the presence of lightweight structural components within?
By using building Collapse Indicators helped firefighters when arriving on the scene of a working fire use the exterior marking on a building that indicates the presence of lightweight structural components within.
Moreover, Structural elements that should be considered as indicators of collapse such as unprotected stool columns and beams exposed to heavy fire. The expansion of structural steel is attacked by the heat of fire. Unprotected light steel and steel beam roofs exposed to severe fire. Cracks or bulges in the wall. Water or smoke pushing through what appears to be a solid masonry wall. Unusual sounds coming from a building or dwelling. Truck traffic will notice soft or spongy feet.
You can learn more about this at:
https://brainly.com/question/12290001#SPJ4
In a delta-connected load, the relation between line voltage and the phase voltage is?
a) line voltage phase voltage
c) line voltage=phase voltage
b) line voltage
d) line voltage phase voltage
The relationship between line voltage and phase voltage in a delta-connected load is line voltage = phase voltage.
What is Line Voltage?
In a three-phase system, line voltage, also known as Vline or VL-L, is the potential difference between any two lines or phases that are present in the system. The phases that are present here are coil windings or conductors.
If R, Y, and B are the three phases, the voltage difference between R and Y, Y and B, or B and R is the line voltage (red, yellow, and blue). Phase voltage is the potential difference between one phase (R, Y, or B) and the neutral junction point, and it is represented by the formula Vphase = VR (voltage of Red phase) = VY (voltage of Yellow phase) = VB.
Line voltage and Phase voltage Relation:
Line voltage and phase voltage are proportional to one another.
That means-
When the line voltage increases, so does the phase voltage.The rise in phase voltage is mirrored in the rise in line voltage.To know more about Delta-connected load, visit: https://brainly.com/question/14909914
#SPJ1
Many solderless connectors are color coded for the size of wire they are designd to work with. WHat size is indicated by the color blue?
Blue insulated connectors used for joining 1.1mm² – 2.5mm² cable sizes.
Green or green with a yellow stripe serves as the protective ground. The neutral wire is white, the hot single phase wires are black, and the second active wire is red. Red, black, and blue three-phase lines.
What is solderless connectors?Solderless connections are ideal when high reliability is not required. Such as components that must be unplugged or replaced on a regular basis or that you anticipate changing in the near future.
Connector tension A solderless device is one that makes a mechanical connection between two or more conductors or between one or more conductors and a terminal without the use of solder.
Solderless strip connectors are used to connect LED strip lights without using solder. They work by inserting the strip into the connectors below. The strip's contact pads slide beneath the connector's contact prongs, completing the electrical circuit.
Strip connectors without soldering do not form a permanent electrical connection with the strip light. While the clasp's teeth do an adequate job of holding the strip in place, movement is still possible - and if there is a lot of it, the contact pads are likely to move away from the contact prongs and lose connection.
To learn more about Solderless connections refer :
https://brainly.com/question/13167697
#SPJ1
a metric 12x1.75 bolt is subjected to a torque of 25 n-m during tightening. if the torque coefficient is 0.18, determine the tensile stress on the bolt (mpa).
The tensile stress on the bolt is 78.29 MPa.
What Exactly Is Tensile Stress?
Tensile stress () is an object's resistance to a force that may rip it apart. It is measured in Newtons/mm2, but was formerly denoted in tons/inch2. It is computed with the maximal strain endured by the object in question without tearing. Tensile stress is defined as the magnitude of force applied along an elastic rod divided by the cross-sectional area of the rod perpendicular to the applied force.
T = C_t x D x sigma x A_s
tensile stress = sigma = T/(C_t x D x A_s)
A_s = (pi/4)x(D - 0.9382xp) ^2
D = 12mm <-- diameter
p = 1.75 <-- pitch
C_t = 0.24 <-- torque coefficient
T = 19000 N-mm <-- torque
A_s = (pi/4)x(12 - 0.9382x1.75)^2 = 84.3 mm^2
tensile stress = 78.29 MPa
To learn more about tensile stress
https://brainly.com/question/25748369
#SPJ4
Why is the reasoning important when you make a scientific argument?