the heaviest invertebrate is the giant squid, which is estimated to have a weight of about 0.34 tons spread out over its length of 33 feet. what is its weight in newtons?

The acceleration of the object is 9.307 m / s when the object of mass (m) slides down an inclined plane and the coefficient of kinetic friction is given.

The resistive force of friction (Fr), which pushes the items together, is divided by the normal or perpendicular force (N), which pushes them apart, to produce the coefficient of friction (fr), which is a numerical value. The following formula represents it: fr = Fr/N.

Calculations:

angle θ = 37°

the coefficient of kinetic friction μ =  0.20

accleration a = g sin θ - μ g cos θ

                  = 5.897 - 1.5653

                  = 4.331 m / s²

(b).  length L = 10 m

initial velocity u = 0

the speed at the bottom of the plane is v

then from the relation v² - u² = 2aL

                               v = √[ 2aL ]

                                 = 9.307 m / s.

Hence, the acceleration of the object is 9.307 m / s.

To know more about the Coefficient of Kinetic friction, check out:

https://brainly.com/question/20241845

#SPJ4

In order from highest to lowest energy, the sections of the electromagnetic spectrum are named as gamma rays, x-rays, ultraviolet radiation, visible light, infrared radiation and radio waves.

The electromagnetic spectrum is the range of all types of electromagnetic radiation. Radiation is the energy that travels and spreads out as it goes - the visible light coming from a lamp in your house and the radio waves that come from a radio station are two types of electromagnetic radiation.

Electromagnetic radiation is an electric and magnetic disturbance travelling through space at the speed of light. It contains neither mass nor charge but travels in packets of radiant energy called photons.

To know more about electromagnetic spectrum:

https://brainly.com/question/27839167

#SPJ4

The power must be supplied to the water to effect this discharge is 28174.32 kW.

The ratio of viscous forces to inertial forces is known as the Reynolds number. A dimensionless number called the Reynolds number is used to group fluid systems where the influence of viscosity plays a significant role in regulating the velocities or the flow pattern of a fluid.

Discharge = Q = 32 m³/s

Velocity of flow=V=Q/A = 32/( π(1.5)²/4)= 18.11 m/s

Reynold's no is given by

Re = VD/v = (18.11)(1.5)/(1.31x10⁻⁶) = 20736641.22

For steel pipe

Roughness = e = 0.045 mm

Relative roughness = E= e/D= (0.045x10⁻³)/1.5=0.00003

Friction factor from Moody's diagram is

f = 0.00988

Apply Bernoulli's theorem b/w top of left reservoirs and exit of pipe

A - denote left reservoir and B- denote exit of pipe

Pa/y + V₂²/2g + Za + hp = Pb/ γ+Vb²/2g + Zb + hf

Where

Pa= Pb=0

Va= 0, Vb = V = 18.11 m/s

Za = (100-95) = 5 m, Zb=(140-95) = 45 m

Frictional head loss =hf = flV²/2gD= (0.00988x300x18.11²)/(2x9.81x1.5)

Frictional head loss = hf = 33.03 m

hp = pump head

Putting values

0+0+5+hp = 0 +18.11²/(2x9.81) +45 +33.03

=> hp = 89.75 m

Power that must be supplied is given by

P = γQhp

P = 9.81x32x89.75

P = 28174.32 kW.

To know more about power visit:

https://brainly.com/question/13787582

#SPJ4

The distance d from the box to the edge of the table if it takes 1.5 s for the box to reach the edge once it begins to move is 1 m

μk = 0.32

t = 1.5 sec

For mass B,

mBg - T = mB a

For mass A,

T - F f = mA a

T - μKmAg = mAa

a = 1.35 × 9.8 - 0.32× 3  × 9.8/ 4.35

a = 0.88 m/[tex]S^{2}[/tex]

vi = 0

d = Vi t + 1/2 a[tex]t^{2}[/tex]

distance d = 0.99 ≈ 1m

Distance is a scalar quantity that describes "how much ground an object has covered" while moving. Displacement is a vector quantity that describes "how far out of place an object is"; it represents the overall shift in position of the object. Distance is a measurement of how far apart two things or locations are, either quantitatively or occasionally qualitatively. Distance in physics or common language can refer to a physical length or an estimate based on other factors (e.g. "two counties over"). The term is also frequently used metaphorically to denote a measurement of the degree of difference between two similar objects (such as statistical distance between probability distributions or edit distance between strings), given that spatial cognition is a rich source of conceptual metaphors in human thought.

Learn more about  distance here:

https://brainly.com/question/12626613

#SPJ4

Red light (660 nm) has a refraction angle of about 43.6°, while violet light (410 nm) has a refraction angle of around 58.3°.

To learn more about the wave theory of light refer to:

https://brainly.com/question/3888556

#SPJ4

The initial total energy of the system equals the final total energy of the system.

The law of conservation of energy states that energy is neither created nor destroyed. For example, if you roll a toy car down a ramp and hit a wall, the energy is converted from kinetic energy to potential energy.

According to the law of conservation of energy is neither created nor destroyed. However, you can convert from one form to another. Taking into account all forms of energy, the total energy of an isolated system is always constant. According to the law of conservation of energy cannot be created or destroyed.

Learn more about The law of conservation here:- https://brainly.com/question/24772394

#SPJ4

The chair is exerting a force of 800N.

Force is a quantity that is used to describe the interaction between two objects. Forces can cause objects to accelerate, decelerate, or change direction. In other words, forces can cause objects to move or change the way they are moving. The weight of an object is a measure of the force of gravity on that object and is calculated by multiplying the object's mass by the acceleration due to gravity.

In the given case, It would need a force equal to his weight (800 N) pressing in the opposite direction for the man to be able to rise up in the chair. Therefore, the 800 N force would be pushed upwards if he were to press down by standing on it.

Read more about the force on:

https://brainly.com/question/27943482

#SPJ4

The mass of the object that the star is orbiting is 7.8 x 1036 kg, or nearly 3,900,000 times that of the Sun.

The orbital velocity law will be used to determine the mass of the core black hole:

M(r)= (rv^2)/G

The star's radius and speed must be converted into meters and meters per second in order to apply this law. 1.0x106 meters per second is the speed that we determine. Since it is specified as 20 light-days, the radius requires a little more work. We may convert to light-days and discover that the orbital radius is also 2.5x10(-2) light-years since there should be roughly 365 light-days in a light-year. Because a light-year is 9.46 x 1015 meters, the orbital radius is 5.2 x 1014 meters. Our calculations lead us to the conclusion that the center black hole's mass is 7.8 x 1036 kg, or nearly 3,900,000 times that of the Sun.

To learn more about Mass Please click on the given link:

https://brainly.com/question/28021242

#SPJ4

The magnitude of the glider's average acceleration is determined as 2.3 m/s².

The average acceleration of the glider is the rate at which the velocity of the glider changes with time.

Mathematically, the formula for average acceleration is given as;

a = v / t

where;

Since the glider is launched by the high winds so that in 45.0 sec the glider's speed equals the speed of the wind.

a = ( 103.33 m/s ) / ( 45 s )

a = 2.3 m/s²

Thus, the average acceleration of the glider is a function of the speed of the glider and the duration to attain such speed.

Learn more about average acceleration here: https://brainly.com/question/26246639

#SPJ1

Answer:

Force = Work/Distance = 70 J/17 m = 4.118 N

Explanation:

i'm smart

The child must exert a force of 4.12 Newtons to pull the sled up the hill.

Force is a fundamental concept in physics that refers to a push or pull on an object. It is an interaction that can cause a change in the motion, shape, or orientation of an object. Force is a vector quantity, which means that it has both magnitude and direction.

Force is measured in Newton's (N) and is defined as the amount of force needed to accelerate a one-kilogram mass at a rate of one meter per second squared. The equation that describes force is F = ma, where F is force, m is mass, and a is acceleration.

There are several types of forces, including:

1. Contact forces: These are forces that act only when two objects are in contact with each other. Examples include friction, tension, and normal force.

2. Non-contact forces: These are forces that act even when two objects are not in contact with each other. Examples include gravity, electric force, and magnetic force.

3. Applied forces: These are forces that are directly applied to an object by a person or an external source. Examples include pushing a book across a table or pulling a sled up a hill.

4. Reactive forces: These are forces that are a reaction to an applied force. For example, if you push a wall, the wall exerts a reactive force back on you.

Understanding force is essential in many fields of science and engineering, as it helps us understand and predict the behavior of objects under different conditions.

Here in the Question,

To calculate the force exerted by the child, we can use the formula:

Work = Force x Distance x cos(theta)

Where:

Work = 70 J

Distance = 17 m

cos(theta) = 1 (assuming the force is exerted in the same direction as the displacement)

Plugging in the values, we get:

70 J = Force x 17 m x 1

Solving for Force, we get:

Force = 70 J / 17 m

Force = 4.12 N

Therefore, the child must exert a force of approximately 4.12 Newtons to pull the sled up the hill.

To learn more about Newton's law of motion click:

brainly.com/question/29775827

#SPJ2

The maximum acceleration of the platform that oscillates at amplitude 2.20 cm and frequency 6.60 hz is 37.8 m/s^2

The acceleration amplitude is  [tex]a_{m}[/tex]=ω²[tex]x_{m}[/tex] ​, where  ω  is the angular frequency (ω=2πf ).

The equation a = v/t denotes acceleration (a), which is the change in velocity (v) over the change in time (t). This enables you to calculate the change in velocity in metres per second squared (m/s2).

Since there are  2π  radians in one cycle.

Therefore, in this circumstance, we obtain  

a=ω²x = (2πf)² x = (2π (6.60))² (0.0220) m = 37.8 m/s^2

To know more about acceleration click here:

https://brainly.com/question/2303856

#SPJ4

The model of the light wave shows many light waves traveling in all directions from a source.

option C is the correct answer.

Wave motion is the transfer of energy and momentum from one point of the medium to another point of the medium without actual transport of matter between two points.

The following explanation illustrates how light waves can travel. Light propagates as electromagnetic waves. Light can travel in all all directions as light waves are spherical waves which travel radially outwards from its source.

From the given image we can conclude the following;

Thus, it is safe to say that the model of light being represented shows many light waves travelling from a single to many direction due to presence of many circular wave path shown in the picture.

Learn more about light waves here: https://brainly.com/question/10728818

#SPJ1

The wavelength of the most intense radiation will decrease.

What is wavelength ?

The distance between two successive crests or troughs of a wave is known as its wavelength. It is calculated using the wave's direction.

The temperature of a blackbody radiator is increased.

Most intense wavelength of light emitted as this increase occurs the wavelength of the most intense radiation will decrease

To learn more about wavelength checkout https://brainly.com/question/13533093

#SPJ4

Total surface area = 3/2 * area of old radiator

From the question, we have

Thermal conductivity is the same in the new and old radiators

We know that,

K = Q/A*ΔT

change in T =  ΔT  

Using this relation, we get

New surface area = 3/2 * area of old radiator

Heat exchanger :

The heat exchanger is a device that transfers heat from one source to another to a working fluid. In both cooling and heating processes, heat exchangers are employed. To avoid mixing, the fluids may be in direct touch or separated by a solid wall. They are frequently utilized in power plants, chemical and petrochemical plants, oil refineries, sewage treatment, air conditioning, refrigeration, and space heating. In an internal combustion engine, a circulating fluid called engine coolant circulates through radiator coils as air passes by the coils, cooling the coolant and heating the incoming air. This is a classic example of a heat exchanger in action.

To learn more about heat exchanger visit: https://brainly.com/question/22595817

#SPJ4

The frequency of sound that the truck driver hears is 1428.57 Hz.

Velocity of the fire engine = V = 40 m/s

Frequency of sound emitted by fire engine = F = 1500 Hz

Velocity of the truck = v = 25 m/s

Frequency of sound that the truck driver listens to = f =

= f = [( V' - V) / (V' - v )} X F

= f = [(343 - 40) / (343 - 25)] X 1500

= f = (303 / 318 ) X 1500

= f = 0.95 X 1500

= f = 1428.57 Hz

To know more about Frequency:

https://brainly.com/question/29558588

#SPJ4

A loop's magnetic flux will alter if it is perpendicular to a uniform magnetic field. if the loop is swapped out for two loops, each of which is half as large.

B = BAcos is the magnetic flux formula. As a result, the flux is at its maximum when B is perpendicular to the wire loop and at zero when there is no magnetic field component perpendicular to the loop.

Multiply the surface area by the portion of the electric field perpendicular to the surface to determine the flux across a given surface. No field lines will flow through the surface if the electric field is perpendicular to it, and the flux will be zero.

To know more about magnetic flux visit:-

https://brainly.com/question/24214683

#SPJ4

The wide pipe's diameter is three times greater than that of the little pipe.

Consider a thin pipe with width r1 and a wide pipe with dimension r2, where v * pi * r12 = v/9 * pi * r22 r12/r2

The wide pipe has a diameter that is three times greater than the narrow pipe because

r1^2/r2^2 = 1/9

r1/r2 = 1/3

We could have the pipe sloping upwards, to make one more straightforward generalization. The fluid would thus gain potential energy in addition to kinetic energy, increasing the work required of the pressure. The increase in potential energy in time t will be (A 1v1t)g(h2h1) if we assume that the center of the area A1 is at height h1, the area A2 is at h2, and we take t to be very small. This changes Bernoulli's equation. Because the flow rate of water in the narrow pipe is higher than the flow rate of the fault in the broad pipe, the pressure drops when water flowing through a broad pipe and into a narrow pipe.

Learn more about wide pipe's here:

https://brainly.com/question/11183247

#SPJ4

The amount of energy that is transferred by a force acting through a distance is known as work.

If we apply a force on an object, this force transforms into kinetic motion and distance is moved by the object. When there is displacement due to this force, work is said to be done.

Work is actually the transfer of mechanical energy from one substance to another. As work is the result of the transfer of energy, it has the same unit as energy, i.e., joule.

When work is done, the kinetic energy of the object is changed, or it has altered potential energy. Potential energy may change into kinetic energy due to the application of force. If position or shape is changed due to force, then we have altered potential energy.

To know more about work here

brainly.com/question/19382352

#SPJ4

The maximum speed of an astronaut is 12.5cm/s.

If, the astronaut uses body mass measurement device to measure her mass, then the speed can be calculated easily.

By differentiating angular frequency, and displacement of mass with respect to time, then speed can be calculated.

We know,

Force constant of the spring, k = 3000 N/m

Mass of an astronaut, m = 69 kg

Amplitude of the oscillation,  x max = 1.9cm = [1.9 cm]*[1 m/100 cm] = 0.019m

We need to find the vmax.

The angular frequency ω is given by,

ω = √[k/m]

The displacement of the mass m from the men position in case of simple harmonic motion is given by,

x = xmax*cos[ωt + φ]

Differentiating above relation with respect to time we get the velocity of the object at any time t during the motion.

v = -ω*xmax*sin[ωt + φ]

v = - vmax*sin[ωt + φ]

Here we have the velocity amplitude {maximum velocity} vmax given as

vmax = ω*xmax

vmax = √[k/m]*xmax

vmax = √[(3000 N/m)/(69kg )]*[0.019 m]

vmax = 0.125m/s        

vmax = 12.5 cm/s

Hence the maximum speed of an astronaut is 12.5cm/s

To know more about speed, click on https://brainly.com/question/29553133

#SPJ4

If the gas is an ideal gas, then the pressure will remain constant in an isothermal process. So the correct option is a.

In general, a gas is compressed by an isothermal process that decreases its volume by a factor of 2. In this process, the pressure will either remain constant (a) .

The behavior of the pressure in an isothermal process depends on the nature of the gas. If the gas is an ideal gas, then the pressure will remain constant since the temperature is constant and the ideal gas law states that pressure is proportional to the temperature. In this case, the answer would be (a).

Finally, if the gas is an ideal gas and the process is adiabatic, then the pressure will increase by a factor less than 2 (c). This is because adiabatic processes involve a decrease in temperature, leading to a decrease in pressure.

Learn more about ideal gas at :https://brainly.com/question/28257995

#SPJ4

Circuit 2 would have the highest resistance and lowest current when the switch is closed.

This is because Circuit 2 has two bulbs in series, meaning that the current must pass through both bulbs to complete the circuit. This increases the overall resistance of the circuit, resulting in a lower current.

Note: This assumes that the other conditions, such as the size and quality of the bulbs and the battery, are the same in all of the circuits. If these conditions change, the resistance and current in the circuits may also change.

Learn more about the Electric Circuits here:

https://brainly.com/question/2969220

#SPJ4

The angular velocity of the wheel with a constant angular acceleration of 2.25 rad/s² clockwise at the beginning of the 4.00 s = 3.8 rad/s.

Angular velocity is the amount of angle traveled per unit time.

The time interval for one rotation is also known as the period, and the angle for one complete rotation is 360 degrees. Usually one full revolution can be written as degrees or radians.

We have,

Angular displacement = 30.0 rad ⇒ θ

Angular speed of the turn table = 1.85 rad/s² ⇒ α

Time of motion, t = 4.0 s ⇒ t

In uniformly variable rotational motion, the angular acceleration is constant.

So,

θ = ω₁t + ½ αt²

30.0 = ω₁ (4) + ½ (1.85) (4.0)²

30.0 = ω₁ (4) + 14.8

4 ω₁ = 30.0 - 14.8

= 15.2

ω₁ = (15.2)/(4)

= 3.8 rad/s

Learn more about angular velocity here:  https://brainly.com/question/29672590

#SPJ4

Answer:That depends on whether both people are pulling in the same direction against a fixed object or pulling against each other. If pulling in the same direction, the total force is 300 N + 300 N = 600 N. If the two people are pulling against each other, the total force is 300 N in the rope is 300 N, or a net of zero.

Explanation:.

Answer:

Close, but not for most humans.  Infrared (IR) is on the edge of what is called the Visible Spectrum.  It is one of many electromagnetic waves that include visibile light IR, ultraviolet, microwaves, radio waves, etc.  

Explanation:

It really depends on how "visible light" is defined.  Humans cannot see IR, but some animals can.  

Electrical conductivity is  the intrinsic property that indicates the ease with which a material is capable of allowing the flow of electric current.

An intrinsic attribute in materials science is independent of both the quantity and the shape of the material, such as a single huge piece or a collection of tiny particles. The basic chemical make-up and structure of the substance are the key determinants of intrinsic qualities.The capacity of a material to carry electricity is known as conductance (also known as electrical conductance). The ability of an electrical current (or flow of charge) to go through a substance is gauged by its conductance. Electrical resistance, denoted as 1/R, is the reciprocal of conductance, or its inverse.Resistance (R) and electrical conductance (G) have a reciprocal relationship: G = 1 R. Electricity's ease of movement through electrical components at a specific voltage differential is measured by electrical conductance. Siemens is the SI unit for conductivity (the older unit was the mho).

To know more about conductivity refer:

https://brainly.com/question/12136944

#SPJ4

13 N/kg The surface gravitational field is given by acceleration due to gravity on the planet (g). Let the value of it on a newly discovered planet be g'.

The gravitational force acting on a mass of one kilogram is measured in newtons. G is assumed to be 9.806 N kg-1 at the surface of the Earth. Additionally, the acceleration of an item falling freely in the gravitational field of the Earth is denoted by the letter "g".

Through the development of his theory of relativity, Albert Einstein demonstrated that gravity is a curvature in the space-time continuum rather than merely a force. Simply explained, an object's mass causes the space around it to essentially bend and curve. That may sound like it belongs in science fiction, but it's true.

To know more about gravitational field visit:

https://brainly.com/question/26690770

#SPJ4

For this situation, I would recommend using a compression spring, as this type of spring will provide the most consistent force over the full range of compression.

What are the applications of Compression Springs?

The applications of compression springs include:

Automobiles: It would be quite challenging to produce the majority of cars without at least some compression springs. In automobiles, compression springs are utilized in a variety of components, including suspension, hoses, and even seats. They are used in the seats to help them adjust to the body and provide comfort. Naturally, a number of sizes and forms are available to accommodate the wide range of uses for car compression springs.

Pens: A ballpoint pen can be used to monitor a compression spring. The pen can write with the tip exposed thanks to this spring, which then covers it inside the housing to keep the ink from drying out. This enables the use of pens without their bulky, losable caps.

Aeronautics: Without various kinds of springs, most air flight would be impossible. Air turbines, navigation systems, engine controls, wheels, brakes, meters, fuel cells, and diesel engines are just a few of the parts of an aeroplane that need springs, even if they may not be visible.

Firearms: When thinking about tension, think about compression springs. Consider the effort required to fire a bow and arrow. If a compression spring is used in place of the human component, the crossbow becomes a far more straightforward weapon.

Compression springs are mechanical springs that are designed to create resistance to a compressive force. Compression springs are typically made with a higher spring constant, which is the measure of how much force is required to compress the spring by a certain amount. With a higher spring constant, a shorter compression is required to achieve the desired launch speed. They are used in many different applications. Compression springs are commonly used to absorb shock, store energy, and return an object back to its original shape after being compressed.

Hence, compression spring is used to reach the targeted launch speed.

To learn more about compression spring from the given link https://brainly.com/question/29678146

#SPJ4

The wave moves in a z-direction. Along the x-axis, there is linear polarization.

As the electric field is directed from one charge to another in a dipole, it oscillates on the x-axis, and the polarization of the electric wave is also on the x-axis because of this. The polarization is linearly polarized along the x-axis and the wave propagates along the z-axis.

To know more about polarization

https://brainly.com/question/14004135

#SPJ4

The wavelength of a 5 Hz wave is  2m that travels with a speed of 10m/s and frequency of 5Hz.

For an electromagnetic wave, we know that there is relation between speed, frequency, and wavelength which is given by

c=ν × λ

where c is defined as the speed of light in any medium,

v is defined as the frequency of the wave,

and λ is defined as the wavelength of the wave

Here c is different for different mediums. Usually in vacuum speed is very high whereas in rough surfaces speed is very low.

So, same formula is applicable to the given wave

Here speed of wave is 10m/sec, frequency of wave=5Hz and wavelength=?

So, putting the values, we get

=>10 = 5 × λ

=>λ=10/5

=>λ=2m

Hence, wavelength is 2m.

To know more about wavelength, visit here:

https://brainly.com/question/13533093

#SPJ4

The distance traveled by dusk is 338.2m.

The rate of change of angular displacement is known as angular speed. The radian per second is the unit of angular speed. Both angular speed and angular velocity are represented using the same formula. Angular velocity is a vector term that describes both magnitude and direction, whereas angular speed describes magnitude.

The scalar measure of the rotation rate is angular speed. The angular distance traveled in one complete rotation is 2 and the time period is (T).

Because the spin rate of the CD is 500 rpm, or revolutions per minute, its angular speed in rad per second equals

w = 500 rev/min * 2π rad/rev * 1/60min/sec

w = 52.36 rad/s

Because the dusk is 3.80 cm from the center, its velocity must be

v = Rw =

v = 3.8 * 52.36

v = 198.97 cm/s

After 2.90 minutes, or 170 seconds, the distance traveled by dusk is

d = v*t

d = 198.97 * 170

d = 33824.9 cm

or

d = 338.2m

Learn more about angular speed here:

https://brainly.com/question/28439806

#SPJ4